Dr.-Ing. Roland Golle

Academic Supervisor

 

Research and Work Focus

Former coordination and deputy head of the Chair of Metal Forming and Casting

Publications

2022

  • Feistle, M.; Golle, R.; Volk, W.: Produktivitätssteigerung in Folgeverbundwerkzeugen. Kongress Stanztechnik, 2022 more…
  • Feistle, M.; Kindsmüller, A.; Pätzold, I.; Golle, R.; Volk, W.: Influence of Sheet Metal Pre-forming on Edge Crack Sensitivity using an AHSS Steel Grade. International Journal of Material Forming 15 (4), 2022 more…
  • Feistle, Martin; Golle, Roland; Volk, Wolfram: Edge Crack Test Methods for AHSS Steel Grades: A Review and Comparisons. Journal of Materials Processing Technology, 2022 more…
  • Schrepfer, A; Schott, A; Tröber, P; Keunecke, M; Welm, M; Steinlehner, F; Golle, R; Volk, W: Reduction of adhesive wear with use of tool coating reducing thermoelectric currents. IOP Conference Series: Materials Science and Engineering 1238 (1), 2022, 012033 more…

2021

  • Kindsmüller, Alexander; Schrepfer, Agnes; Stahl, Jens; Pätzold, Isabella; Nürnberger, Anian; Golle, Roland; Volk, Wolfram: Influence of cutting parameters on mechanisms causing slug pulling. Production Engineering, 2021 more…
  • Müller, D.; Stahl, J.; Nürnberger, A.; Golle, R.; Tobie, T.; Volk, W.; Stahl, K.: Shear cutting induced residual stresses in involute gears and resulting tooth root bending strength of a fineblanked gear. Archive of Applied Mechanics, 2021 more…
  • Müller, Daniel; Stahl, Jens; Nürnberger, Anian; Golle, Roland; Tobie, Thomas; Volk, Wolfram; Stahl, Karsten: Shear cutting induced residual stresses in involute gears and resulting tooth root bending strength of a fineblanked gear. Archive of Applied Mechanics 91 (8), 2021, 3679-3692 more…
  • Stahl, Jens; Pätzold, Isabella; van den Bosch, Lucas; Kindsmüller, Alexander; Golle, Roland; Volk, Wolfram: The Frictional Force between Slug and Die in Shear Cutting after Material Separation. Key Engineering Materials 883, 2021, 285-293 more…
  • Tröber, Philipp; Welm, Markus; Weiss, Hannes A.; Demmel, Peter; Golle, Roland; Volk, Wolfram: Temperature, thermoelectric current and adhesion formation during deep drawing. Wear 477, 2021, 203839 more…

2020

  • Stahl, J.; Pätzold, I.; Golle, R.; Sunderkötter, C.; Sieurin, H.; Volk, W.: Effect of One- and Two-Stage Shear Cutting on the Fatigue Strength of Truck Frame Parts. Journal of Manufacturing and Materials Processing, 2020 more…
  • Welm, M.; Tröber, P.; Weiss, H. A.; Demmel, P.; Golle, R.; Volk, W.: Thermoelectrically Based Approaches to Reduce Adhesive Wear During Blanking. JOM - The Journal of The Minerals, Metals & Materials Society (TMS) 72, 2020 more…
  • Welm, Markus; Tröber, Philipp; Weiss, Hannes Alois; Demmel, Peter; Golle, Roland; Volk, Wolfram: A Thermoelectrically Based Approach to Reduce Adhesive Wear During Blanking. In: The Minerals, Metals and Materials Society (Ed.): TMS 2020 149th Annual Meeting & Exhibition Supplemental Proceedings. Springer International Publishing, 2020, 1993-2007 more…

2019

  • Feistle, M.; Pätzold, I.; Golle, R.; Volk, W.: Open hole tensile tests for the determination of the edge-crack sensitivity of sheared holes dependent on specimen geometry, cutting parameters, and the notch factor. Procedia Manufacturing 29, 2019, 412-419 more…
  • Mittler, T.; Greß, T.; Feistle, M.; Krinninger, M.; Hofmann, U.; Riedle, J.; Golle, R.; Volk, W.: Fabrication and processing of metallurgically bonded copper bimetal sheets. Journal of Materials Processing Technology 263, 2019, 33-41 more…
  • Neumayer, F.; Vogt, S.; Gueffroy, M.; Jesner, G.; Kelsch, R.; Geile, M; Sommer, A.; Golle, R.; Volk, W.: Warm and cold blanking of manganese-boron steel 22MnB5 with different tool geometries. Procedia Manufacturing 29, 2019, 345-352 more…
  • Stahl, J.; Müller, D.; Pätzold, I.; Golle, R.; Tobie, T.; Volk, W.; Stahl, K.: The Influence of Residual Stresses Induced by Near-Net-Shape Blanking Processes on the Fatigue Behavior under Bending Loads. IOP Conference Series: Materials Science and Engineering 651, 2019, 012086 more…
  • Tröber, P.; Welm, M.; Weiss, H.; Demmel, P; Golle, R.; Volk, W.: The influence of process parameters and sheet material on the temperature development in the forming zone. Manufacturing Review 6, 2019 more…
  • Weiss, H.A.; Steentjes, S.; Tröber, P.; Leuning, N.; Neuwirth, T.; Schulz, M.; Hameyer, K.; Golle, R.; Volk, W.: Neutron grating interferometry investigation of punching-related local magnetic property deteriorations in electrical steels. Journal of Magnetism and Magnetic Materials 474, 2019, 643-653 more…

2018

  • Feistle, M.; Pätzold, I.; Golle, R.; Volk, W.; Frehn, A.; Ilskens, R.: Maximizing the Expansion Ratio through Multi-stage Shearcutting Process during Collar Forming. IOP Conf. Series: Materials Science and Engineering 418, 2018 more…
  • Paetzold, I.; Feistle, M.; Golle, R.; Volk, W.; Frehn, A.; Ilskens, R.: Determination of the minimum possible damage due to shear cutting using a multi-stage shear cutting process. International Deep Drawing Research Group 37th Annual Conference, 2018 more…
  • Stahl, J.; Müller, D.; Tobie, T.; Golle, R.; Volk, W.; Stahl, K.: Residual Stresses in Parts Manufactured by Near-Net-Shape-Blanking. Production Engineering – Research and Development, 2018 more…
  • Tröber, P.; Welm, M.; Weiss, H. A.; Demmel, P.; Golle, R.; Volk, W.: Einfluss verschiedener Prozessparameter auf die Temperaturentwicklung in der Umformzone beim Durchsetzen von Vergütungsstahl. Dry Metal Forming Open Access Journal 4, 2018, 47-51 more…
  • Tröber, P.; Welm, M.; Weiss, H. A.; Demmel, P.; Golle, R.; Volk, W.: The influence of process parameters on the temperature development in the forming zone. MATEC Web of Conferences (190), 2018 more…

2017

  • Cha, W.; Hammer, T.; Gutknecht, F.; Golle, R.; Tekkaya, A. E.; Volk, W.: Adaptive Wear Model for Shear-Cutting Simulation with Open Cutting Line. Wear 386-387, 2017, 17-28 more…
  • Feistle, M.; Koslow, I.; Krinninger, M.; Golle, R.; Volk, W.: Reduction of burr formation for conventional shear cutting of boron-alloyed sheets through focused heat treatment. Procedia CIRP 63C (2017), 2017, 493-498 more…
  • Feistle, M.; Krinninger, M.; Pätzold, I.; Stahl, J.; Golle, R.; Volk, W.: Design and conceptualization of a cutting tool to investigate the influence of the shear cutting process on edge crack sensitivity. 36th IDDRG Conference Materials Modelling and Testing for Sheet Metal Forming, Journal of Physics, 2017 more…
  • Gläsner, T.; Sunderkötter, C.; Hoffmann, H.; Volk, W.; Golle, R.: Development of a 2-stage shear-cutting-process to reduce cut-edge-sensitivity of steels. Journal of Physics: Conference Series 896, 2017, 012104 more…
  • Krinninger, M.; Feistle, M.; Golle, R.; Volk, W.: Notch Shear Cutting of Aluminium Alloys. 17th International Conference on Sheet Metal, SHEMET17, 2017, 53-58 more…
  • Krinninger, M.; Opritescu, D.; Golle, R.; Volk, W.: On the opportunities of problem- and process-adapted shear cutting simulations for effective process design. International Conference on the Technology of Plasticity, 2017 more…
  • Krinninger, M.; Steinlehner, F.; Opritescu, D.; Golle, R.; Volk, W.: On the Influence of Different Parameters on the Characteristic Cutting Surface when Shear Cutting Aluminum. Procedia CIRP , 2017, 230-236 more…
  • Krinninger, Michael; Steinlehner, Florian; Opritescu, Daniel; Golle, Roland; Volk, Wolfram: On the Influence of Different Parameters on the Characteristic Cutting Surface when Shear Cutting Aluminum. Procedia CIRP 63, 2017, 230-235 more…
  • Pätzold, I.; Dittmann, F.; Feistle, M.; Golle, R.; Hoffmann, H.; Volk, W.: Influence of shear cutting parameters on the fatigue behavior of a dual-phase steel. 36th IDDRG Conference Materials Modelling and Testing for Sheet Metal Forming, Journal of Physics, 2017 more…
  • Stahl, J.; Tröber, P.; Feistle, M.; Golle, R.; Volk, W.: An inverse approach for the geometry prediction of sheetmetal. 36th IDDRG Conference Materials Modelling and Testing for Sheet Metal Forming, 2017 more…
  • Vogt, S.; Neumayer, F.; Serkyov, I.; Jesner, G.; Kelsch, R.; Geile, M.; Sommer, A.; Golle, R.; Volk, W.: Experimental evaluation of tool wear throughout a continuous stroke blanking process of quenched 22MnB5 ultra-high-strength steel. 36th IDDRG Conference Materials Modelling and Testing for Sheet Metal Forming, 2017 more…
  • Weiss, H. A.; Tröber, P.; Golle, R.; Steentjes, S.; Leuning, N.; Hameyer, K.; Volk, W.: Loss reduction due to blanking parameter optimization for different non-grain oriented electrical steel grades. Electric Machines and Drives Conference (IEMDC), 2017 IEEE International, 2017 more…
  • Weiss, H.; Golle, R.; Hoffmann, H.; Volk, W.: Auswirkung des Stanzprozesses auf den Wirkungsgrad von Elektromotoren. 9. Kongress Stanztechnik, 2017 more…

2016

  • Feistle, M.; Golle, R.; Volk, W.: Determining the influence of shear cutting parameters on the edge cracking susceptibility of high-strength-steels using the edge-fracture-tensile-test. 48th CIRP Conference on Manufacturing Ssystems - CIRP CMS 2015, 2016 more…
  • Feistle, M.; Pätzold, I.; Golle, R.; Volk, W.: Predicting Edge Cracks on Shear-Cut High-Strength Steels by Modified Uniaxial Tensile Tests. Journal of Key Engineering Materials Vol. 703, 2016, 49-55 more…
  • Hammer, T.; Cha, W.-G.; Feistle, M.; Golle, R.; Volk, W.: FE-unterstützte Verschleißprognose beim Scherschneiden unter Berücksichtigung verschiedener Verschleißmechanismen. 9. Forum Tribologische Entwicklungen in der Blechumformtechnik, Meisenbach Verlag GmbH, 2016, 59-71 more…
  • Kopp, T.; Stahl, J.; Demmel, P.; Tröber, P.; Golle, R.; Hoffmann, H.; Volk, W.: Experimental investigation of the lateral forces during shear cutting with an open cutting line. Journal of Materials Processing Technologiy Volume 238, 2016, 49-54 more…
  • Krinninger, M.; Opritescu, D.; Golle, R.; Volk, W.: Experimental investigation of the influence of punch velocity on the springback behaviour and the flat length in free bending. Procedia CIRP  41, 2016, 1066-1071 more…
  • Suh, J.; Victoria-Hernández, J.; Letzig, D.; Golle, R.; Volk, W.: Enhanced mechanical behavior and reduced mechanical anisotropy of AZ31 Mg alloy sheet processed by ECAP. Materials Science and Engineering: A 650, 2016, 523-529 more…
  • Suh, J.; Victoria-Hernández, J.; Letzig, D.; Golle, R.; Volk, W.: Effect of processing route on texture and cold formability of AZ31 Mg alloy sheets processed by ECAP. Materials Science and Engineering: A 669, 2016, 159-170 more…
  • Tröber, P.; Golle, R.; Volk, W.: Experimental investigation on the thermoelectric current during embossing of Aluminum EN AW 1050. Dry Metal Forming Open Access Journal FMT 2, 2016, 40-43 more…

2015

  • Demmel, P.; Hoffmann, H.; Golle, R.; Intra, C.; Volk, W.: Interaction of heat generation and material behaviour in sheet metal blanking. CIRP Annals - Manufacturing Technology 64 (1), 2015, 249-252 more…
  • Feistle, M.; Krinninger, M.; Golle, R.; Volk, W.;: Notch Shear Cutting of Press Hardened Steels. Journal of Key Engineering Materials Vol. 639, 2015, 477-484 more…
  • Gläsner, T.; Schaffner, T.; Sunderkötter, C.; Volk, W.; Hoffmann, H.; Golle, R.: Studies on the effect of tool wear on the production process in two stage shear cutting. Key Engineering Materials 651-653, 2015, 1261-1270 more…
  • Kopp, T.; Golle, R.; Hoffmann, H.; Volk, W.: Einfluss der Werkzeugsteifigkeit auf die Standmenge von Stanzwerkzeugen. 7. Kongress Stanztechnik, 2015 more…
  • Letzig, D.; Suh, J.; Bohlen, J.; Yi, S.; Kurz, G.; Golle, R.; Volk, W.; Victoria-Hernandez, J.: On the Development of Mg Sheets with Improved Formability by Applying Additional Shear Strain during Processing. Material Science Forum, 2015, 395-400 more…
  • Mackensen, A.; Golle, M.; Golle, R.; Hoffmann, H.: Force reduction during blanking operations of AHSS sheet materials. In: Tekkaya, A. E.; Homberg, W.; Brosius, A. (Ed.): 60 Excellent inventions in metal forming. Springer, 2015, 205-210 more…
  • Suh, J.; Victoria-Hernandez, J.; Letzig, D.; Golle, R.; Yi, S.; Bohlen, J.; Volk, W.: Improvement in cold formability of AZ31 magnesium alloy sheets processed by equal channel angular pressing. Journal of Materials Processing Technology 217, 2015, 286-293 more…

2014

  • Feistle, M.; Demmel, P.; Golle, R.; Volk, W.: Bestimmung und Optimierung der prozessbeeinflussenden Parameter beim Durchsetzen hochfester Stähle. NEBU 2014, Neuere Entwicklungen in der Blechumformung, 2014 more…
  • Gläsner, T.; Sunderkötter, C.; Plath, A.; Bednarz, M.; Volk, W.; Hoffmann, H.; Golle, R.: Methods to decrease cut edge sensitivity of high strength steels. 17th Conference of the European Scientific Association on Material Forming, ESAFORM 2014, 2014, 1294-1307 more…
  • Jocham, D.; Golle, R.; Volk, W.: Wear behavior of austempered ductile Iron (ADI) in cutting and forming tools. IDDRG 2014 - Innovations for the sheet metal industry, 2014, 393-398 more…
  • Sachnik, P.; Volk, W.; Golle, R.; Hofmann, H.: The influence of temperature on zinc abrasion in deep drawing processes. 17th Conference of the European Scientific Association on Material Forming, ESAFORM 2014, 2014, 1039-1046 more…
  • Suh, J.; Victoria-Hernandez, J.; Letzig, D.; Golle, R.; Yi, S.; Bohlen, J.; Volk, W.: Improvement in cold formability of AZ31 Mg alloy sheets processed by equal channel angular pressing. The 2nd German-Korean Workshop on the production and industrial applications of semi-finished Mg products, 2014 more…
  • Suh, J.; Victoria-Hernandez, J.; Letzig, D.; Golle, R.; Yi, S.; Bohlen, J.; Volk, W.: Improvement of ductility at room temperature of Mg-3Al-1Zn alloy sheets processed by equal channel angular pressing. 11th International Conference on Technology of Plasticity, ICTP 2014, 2014 more…
  • Suh, J.; Victoria-Hernandez, J.; Letzig, D.; Golle, R.; Yi, S.; Bohlen, J.; Volk, W.: Improvement of ductility at room temperature of Mg-3Al-1Zn alloy sheets processed by equal channel angular pressing. Procedia Engineering 81, 2014, 1517-1522 more…
  • Volk, W.; Feistle, M.; Golle, R.; Opritescu, D.: Advances in the Shear Cutting of Press Hardened Steels. Warm and Hot Forming, University of Twente, 2014, 41-46 more…

2013

  • Demmel, P.; Golle, R. ; Hoffmann, H. ; Volk, W.: Thermische Beanspruchung der Schneidkante beim Scherschneiden. 5. Kongress Stanztechnik, 2013 more…
  • Demmel, P.; Pazureck, A.; Golle, R.; Volk, W., Hoffmann, H.: Characterization of the thermoelectric behavior of plastically deformed steels. Journal of Electronic Materials, 2013 more…
  • Demmel, P.; Tröber, P.; Kopp, T.; Golle, R.; Volk, W.; Hoffmann, H.: Characterization of the thermoelectric behavior of plastically deformed steels by means of relative Seebeck coefficient. Materials Science Forum 755, 2013, 1-7 more…
  • Mair, J.; Canti, R.; Golle, R.; Volk, W.; Hoffmann, H.: Dynamic strength behaviour of punch connections in shear cutting processes. 15th International Conference on Sheet Metal (SHEMET) / Key Engineering Materials, 2013, 262-269 more…

2012

  • Demmel, P.; Nothhaft, K.; Golle, R.; Hoffmann, H.: Zerteilen. In: Spur, Günter; Neugebauer, Reimund; Hoffmann, Hartmut (Ed.): Handbuch Umformen. Carl Hanser Verlag, 2012, 679-729 more…
  • Demmel, Peter; Kopp, Thomas; Golle, Roland; Volk, Wolfram; Hoffmann, Hartmut: Experimental Investigation on the Temperature Distribution in the Shearing Zone During Sheet Metal Blanking. Steel Research International, 2012 more…
  • Demmel, Peter; Hirsch, Martin; Golle, Roland; Hoffmann, Hartmut: In Situ Temperature Measurement in the Shearing Zone during Sheet Metal Blanking. Advanced Materials Research 445, 2012, 207-212 more…
  • Neugebauer, R.; Kräusel, V.; Barthel, T.; Volk, W.; Hoffmann, H.; Golle, R.; Kopp, T.: Entwicklung kalkulatorischer Kenngrößen zur Gestaltung von Scherschneidprozessen und Bewertung der Bauteilqualität bei Anwendung hoher Schneidgeschwindigkeiten. 32. EFB-Kolloquiums Blechverarbeitung / EFB-Tagungsband Nr. 33, Europäische Forschungsgesellschaft für Blechverarbeitung e.V. (EFB), 2012, 179-192 more…
  • Opritescu, D.; Sachnik, P.; Yang, Z.; Golle, R.; Volk, W.; Hoffmann, H.; Schmiedl, F.; Ritter, M.; Gritzmann, P.: Automated Driving by Standardizing and Scaling the Manufacturing Strategy. Procedia CIRP 3, 2012, 138-143 more…
  • So, H.; Faßmann. D.; Hoffmann, H.; Golle, R.; Schaper, M.: An investigation of the blanking process of the quenchable boron alloyed steel 22MnB5 before and after hot stamping process. Journal of Materials Processing Technology 212 (2), 2012, 437-449 more…

2011

  • Hirsch, M.; Golle, R.; Hoffmann, H.: Tool-Endurance of High-Speed Stamping Tools with Plates of Magnesium and Carbon Fibre Laminate. Steel Research International, Special Edition: 10th International Conference on Technology of Plasticity (ICTP), 201125.09.2011-30.09.2011, 564-569 more…
  • Hirsch, M.; Krönauer, B.; Golle, R.; Hoffmann, H.; Golle, M.; Jesner, G.: Innovative Tools and Tool Steels for the Blanking of Press-Hardened Ultra High-Strength Manganese-Boron Steels. International Conference on Advances in Materials and Processing Technologies (AMPT) / Advances in Materials and Processing Technologies II (Advanced Materials Research), TRANS TECH PUBLICATIONS LTD, 201126.10.2009-29.10.2009, 123-128 more…
  • Hirsch, Martin; Demmel, Peter; Golle, Roland; Hoffman, Hartmut: Light Metal in High-Speed Stamping Tools. 14th International Conference on Sheet Metal (SHEMET) / Key Engineering Materials, TRANS TECH PUBLICATIONS LTD, 2011, 259-266 more…
  • Kim, J.; Suh, J.; Hoffmann, H.; Golle, R.: Determination of uniaxial flow stress curve using aero-bulge test for very thin copper sheet. International Conference on Advances in Materials and Processing Technologies, AMPT 2009, 2011, 608-613 more…
  • Neugebauer, R.; Kräusel, V.; Barthel, T.; Hoffmann, H.; Golle, R.; Kopp, T.: Entwicklung kalkulatorischer Kenngrößen zur Gestaltung von Scherschneidprozessen und Bewertung der Bauteilqualität bei Anwendung hoher Schneidgeschwindigkeiten. 31. EFB-Kolloquium Blechverarbeitung / EFB-Tagungsband T32, Europäische Forschungsgesellschaft für Blechverarbeitung e.V. (EFB), 2011, 161-173 more…
  • Nürnberg, G.; Jing, X.; Scherer, D.; Ersoy-Nürnberg, K.; Golle, R.; Bohlen, J.; Fuskova, L.; Letzig, D.; Hoffmann, H.: Improving the sheared edge in the blanking of commercial AZ31 sheet through texture modification. Journal of Materials Processing Technology 211 (12), 2011, 2022-2031 more…
  • Volk, Wolfram; Hoffmann, Hartmut; Golle, Roland; Kopp, Thomas: Herausforderungen bei der wirtschaftlichen Umsetzung von Mischbaukonzepten. Tagungsband, CBC 2011, 6. Chemnitzer Karosseriekolloquium, Verlag Wissenschaftliche Scripten, 2011 more…

2010

  • Hoffmann, H; Golle, R.; Demmel, P.; Mair, J.; Nürnberg, G.; Ostermair, M.: Advances in Forming and Shearing Technologies. International Conference on Competitive Manufacturing COMA'10, 2010 more…
  • Kim, J.; Golle, R.; Hoffmann, H.: Investigation of size effects of very thin aluminum and copper sheets using aero-bulge test. Materials Science and Engineering: A; Structural Materials: Properties, Microstructure and Processing 527 (27-28), 2010, 7220–7224 more…
  • Krönauer, B.; Hirsch, M.; Golle, R.; Hoffmann, H.; Golle, M.; Jesner, G.: Beschneiden von pressgehärteten Blechen - Ultrahochfestes 22MnB5-Blech im Scherschneidprozess. Zeitschrift für wirtschaftlichen Fabrikbetrieb (ZWF) (01-02/2010), 2010, 26-30 more…
  • Krönauer, B.; Hirsch, M.; Golle, R.; Hoffmann, H.; Golle, M.; Jesner, G.; Pelloso, G.; Baron, L.; Hermann, M.: Further Results in Blanking Form-Hardened Ultra High Strength Manganese-Boron-Steels with Innovative Tools and Tool Steels. 50th anniversary conference 2010 IDDRG, 201031.05.2010-02.06.2010 Graz more…
  • Mackensen, A.; Golle, M.; Golle, R.; Hoffmann, H.: Experimental investigation of the cutting force reduction during the blanking operation of AHSS sheet materials. CIRP Annals - Manufacturing Technology 59 (1), 2010, 283-286 more…
  • Sartkulvanich, P.; Krönauer, B.; Golle, R.; Konieczny, A.; Altan, T.: Finite element analysis of the effect of blanked edge quality upon stretch flanging of AHSS. CIRP Annals - Manufacturing Technology 59 (1), 2010, 279-282 more…

2009

  • Hirsch, M.; Golle, R.; Hoffmann, H.: Displacements in Punching Dies and their Effect on Tool Endurance. 8th International Tooling Conference (TOOL09), Verlag Mainz, 2009 more…
  • Hoffmann, H.; Golle, R.; Demmel, P.; Mair, J.; Nürnberg, G.; Hörmann, F.: Extension of blanking applications through innovation. Tagungsband des Feintool University Colloquium, 2009 more…
  • Kim, J.; Hoffmann, H.; Golle, M.; Golle, R.: Untersuchung zum Werkstoffverhalten von sehr dünnen Kupferblechen. DFG-Abschlusskolloquium SPP 1138 Prozessskalierung, BIAS Verlag, 200911.02.2009-12.02.2009, 267-286 more…
  • Kim, J.; Suh, J.; Hoffmann, H.; Golle, R.: Determination of uniaxial flow stress curve using Aero-bulge test for very thin copper sheet. International Conference on Advances in Materials and Processing Technologies (AMPT), TRANS TECH PUBLICATIONS LTD, 2009, 608-613 more…
  • Mackensen, A.; Golle, M.; Golle, R.; Hoffmann, H.: Determination of the Hole Expansion Properties of AHSS using an Optical 3D Deformation System. IDDRG Proceedings, 200901.06.2009-03.06.2009, 547-558 more…
  • Maier-Komor, P.; Golle, R.; Hoffmann, H.: Nachbearbeitungsfreies Schneiden geschlossener Profile mit dem Impulsmagnetverfahren. Kolloquium Impulsmagnetumformung, 2009 more…
  • So, H.; Hoffmann, H.; Golle, R.: Blanking of press hardened ultra high strength steel. 2nd International conference on HOT SHEET METAL FORMING OF HIGH-PERFORMANCE STEEL (CHS2), 200915.06.2009-17.06.2009 more…

2008

  • So, H.; Hoffmann, H.; Golle, R.: Schneidstrategien zum wirtschaftlichen Zerteilen pressgehärteter Stahlbleche. Tagungsband zum 3. Erlanger Workshop Warmblechumformung, 2008, 149 - 168 more…

2007

  • Hoffmann, H.; Golle, R.; Kim, J.; Hong, S.: Determination of the biaxial flow stress curve of very thin 99.5% Aluminum sheets. CIRP special session keynote paper 2007, 2007 more…
  • Hoffmann, Hartmut; Nuernberg, Gerald; Ersoy, Kivilcim; Herrmann, Gernot; Golle, Roland: Simulationsgestützte Verschleißberechnung durch Ermittlung von Verschleißkoeffizienten bei der Blechumformung. Tagungsband T27 des EFB-Kolloquiums Blechverarbeitung „Neue Wege zum wirtschaftlichen Leichtbau - Innovative Lösungen zur Blechumformung und mechanischen Fügetechnik“, Europäische Forschungsgesellschaft für Blechverarbeitung e.V. (EFB), 2007am 6. und 7. März 2007 in Fellbach more…
  • Nürnberg, G.; Ersoy, K.; Herrmann, G.; Golle, R.; Hoffmann, H: Verschleißsimulation in der Blechumformung. Maschinenmarkt , 2007 more…

2006

  • Nuernberg, G.; Ersoy, K.; Herrmann, G.; Golle, R.; Hoffmann, H.: Verschleißverhalten von Umformwerkzeugen in der Großserie und dessen numerische Berechnung. Proceedings 5th Virtual Materials Processing Focus: Metals, Kompetenzzentrum Neue Materialien Nordbayern, 2006 more…
  • Nuernberg, G.; Ersoy, K.; Herrmann, G.; Golle, R.; Hoffmann, H.:: Verschleißverhalten von Umformwerkzeugen in der Großserie und dessen numerische Berechnung. Tagungsband zum 5th Virtual Materials Processing Focus: Metals, 200628.11.2006 - 29.11.2006 more…
  • Schilp, H.; Golle, R.; Petry, R.: Einfluss von Werkzeugwerkstoff und Oberfläche auf die Flitterbildung beim Scherschneiden von Aluminiumblechen im offenen Schnitt. Galvanotechnik (8/2006), 2006, 1838-1844 more…

2005

  • Schilp, H.; Golle, R.; Petry, R.: Einfluss von Werkzeugwerkstoff und Oberfläche auf die Flitterbildung beim Scherschneiden von Aluminiumblechen im offenen Schnitt. Berichtsband über das 27. Ulmer Gespräch am 28. und 29. April 2005 in Neu-Ulm, 2005 more…

2004

  • Schilp, H.; Hoffmann, H.; Golle, R.: Bis zu 97 % weniger Flitter beim Schneiden von Aluminiumblech. contact, 2004 more…
  • Schilp, H.; Hoffmann, H.; Golle, R.; Hoogen, M.: Flitterreduzierung beim Schneiden von Aluminiumblech. Blech Rohre Profile (2/2004), 2004, 78-79 more…
  • Schilp, H.; Hoffmann, H.; Golle, R.; Hoogen, M.: Reduzierung der Flitterbildung durch optimierte Werkzeugparameter beim Beschneiden von Aluminiumblechteilen. Neuere Entwicklungen in der Blechumformung, MAT-INFO, Werkstoff-Informationsges., 2004 more…
  • Schilp, H.; Hoffmann, H.; Golle, R.; Hoogen, M.: Blanking Aluminium Sheet Metal Parts - Reduction of Flaking by Optimizing Tool Parameters. New Developments in Sheet Metal Forming Technology, Mat-Info, 2004Fellbach; 10.05.2004-12.05.2004, 267-280 more…

2003

  • Schilp, H.; Hoffmann, H.; Golle, R.; Hoogen, M.: Einfluss von Schneidparametern und Werkzeugwerkstoffen auf Kaltaufschweißungen. UTF Science (IV/2003), 2003 more…
  • Schilp, H.; Hoffmann, H.; Golle, R.; Hoogen, M.: Möglichkeiten der Flittermengenreduzierung beim Scherschneiden von Aluminium. VDI Wissensforum, 2003Tragende Hybridstrukturen more…

2002

  • Hwang, C.; Golle, R.; Hoffmann, H.: Numerical method to estimate the wear of a tool in sheet metal forming. Numisheet, 2002 more…
  • Hwang, C.; Golle, R.; Hoffmann, H.: Numerical Approach to minimize tool wear in the sheet metal forming. 7th International Conference on Technology of Plasticity, 2002 more…

1998

  • Kopietz, J.; Golle, R.; Schnabel, J.; Dinkel, F.; Hoffmann, H.: Tiefziehbleche lackieren. Werkstatt und Betrieb , 1998, 928-933 more…

1997

  • Hoffmann, H ; Golle, R ; Hein, P: Applications for a high frequency ultra sound inspection system. Blech Rohre Profile 44 (1-2), 1997, 42-45 more…

Patents

  • Semmler, S.; Michel, T.; Wimmer, T.; Lang, R.; Donath, N.; Wasmuth, U.; Golle, R.:
    Verfahren zum Fügen mindestens zweier Bauteile und Blindnied zur Durchführung des Verfahrens
    Offenlegungsschrift: DE 10 2004 006 344; 2005
  • Thomas, V.; Hoffmann, H.; Golle, R.:
    Ziehteile aus Federstahlblech, insbesondere als Leichtbau- oder Karosserieteil
    Offenlegungsschrift: DE 198 15 022; 1999
  • Hoffmann, H.; Golle, R.; Loibl, D.:
    Verstellbares Werkzeug
    Patentschrift: DE 197 56 232; 1999
  • Golle, R.; Hoffmann; H.; Thomas, V.:
    Umformbares, bereits vorgeformtes, dünnwandiges Halbfabrikat aus insbesondere Metall
    Offenlegungsschrift: DE 197 37 969; 1998
  • Hoffmann, H.; Golle, R.; Schäfer, B.:
    Antriebseinrichtung für eine schnelllaufende Stanz- und Schneidpresse
    Offenlegungsschrift: DE 197 22 245; 1998
  • Bogon, P.; Erdmann, C.; Golle, R.; Grünbaum, M.; Hoffmann, R.; Hoogen, M.; Roll, K.:
    Vorrichtung zum Umformen oder Zerteilen von Werkstücken mit integrierter Absaugeinrichtung
    Offenlegungsschrift: DE 103 57 923; 2005
  • Heinzmann, D.; Kopietz, J.; Meinhardt, J.; Bevc, B.; Schwimmbeck, H.; Ederer, A.; Golle, R.; Hoffmann, H.:
    Verfahren zur Oberflächenvergütung
    Patentschrift: DE 100 59 802; 2008
  • Kopietz, J.; Meinhardt, J.; Golle, R.; Voelkner, W.; Hoffmann, H.:
    Verfahren zur Ermittlung von Umform- Kenngrößen an Blechformteilen
    Patentschrift: DE 100 02 684; 2002
  • Golle, R.; Kuschke, J.; Hoffmann, H.; Hoogen, M.:
    Herstellverfahren für ein Bauteil aus einem Rohr aus kaltumformbarem Material, insbesondere Metall
    Europäische Patentschrift: EP 0 894 55; 1998